Choosing The Right Wood Screw Size

Box of TIMCO Classic multi-purpose PZ double countersunk wood screws

Pick a screw that is too short and the joint pulls apart; too long and it bursts through the other side. Too thin and it snaps or strips, too thick and it splits the timber. The good news is that a handful of simple rules will get the size right for almost every woodworking and fitting job. This guide explains how wood screw sizes work and how to choose the right one.

How Wood Screw Sizes Are Written

Screws sold in the UK are sized in millimetres as diameter x length. A 4.0 x 40mm screw has a 4mm thread diameter and is 40mm long. For countersunk screws the length is measured from the top of the head to the tip, because the whole screw ends up buried in the timber.

You will still see older gauge numbers on plans and some packaging. These are the approximate equivalents:

Metric Diameter Approximate Gauge Typical Uses
3.0mm No. 4 Small hinges, catches, light fittings
3.5mm No. 6 Hinges, brackets, thin boards
4.0mm No. 8 General joinery, cabinets, shelving
4.5mm No. 9 Decking, heavier joinery
5.0mm No. 10 Framing, battens, fixing to walls with plugs
6.0mm No. 12 Heavy fixings, gate and shed work

Choosing The Length

The screw does its work in the second piece of timber – the one you are fixing into. Two rules of thumb work well together:

  • About two and a half times the thickness of the piece you are fixing. For an 18mm board, that points to a 40–50mm screw.
  • At least half, and ideally two thirds, of the screw in the base piece. A 40mm screw through an 18mm board leaves 22mm in the timber behind.

Always check that the screw will not come out of the far side or hit anything behind, such as pipes and cables in a wall.

Choosing The Diameter

A thicker screw is stronger, but it is also more likely to split timber, especially near ends and edges and in hardwoods. As a guide:

  • 3.5mm for small hardware, hinges and thin material
  • 4.0mm for most furniture, cabinet and general DIY work
  • 4.5–5.0mm for structural timber, battens, decking and heavier joints
  • 6.0mm and above for heavy-duty fixings – consider a coach screw for big loads

When fixing into a wall plug, match the screw diameter to the plug. Our Plasterboard Fixings Guide includes a plug and screw size chart.

Worked Examples

Job Screw Size To Start With
Fixing 18mm board to an 18mm carcass edge 4.0 x 40mm
Fixing a 25mm batten to a stud 4.0 x 60mm or 5.0 x 60mm
Hinges, catches and small brackets 3.5 x 15–20mm or 4.0 x 15mm
Decking boards to joists 4.5 x 50–70mm decking screws
Joining two 47mm timbers 5.0 x 80–100mm

Pilot And Clearance Holes

Modern multi-purpose screws with sharp points often go into softwood without a pilot hole, but there are times you should always drill one:

  • Hardwoods such as oak, which split and can snap screws
  • Near the end or edge of a board, where the timber is most likely to split
  • Thin or brittle material, including some MDF edges

Drill the pilot hole roughly the size of the solid core of the screw, not the outside of the thread. For a tight joint, drill a clearance hole the size of the screw shank through the top piece, so the thread only grips the base piece and pulls the two together.

Fully Or Partially Threaded?

Partially threaded screws, such as the TIMCO Velocity, have a plain shank under the head that slides through the top piece, so the screw clamps two timbers tightly together. Fully threaded screws, such as TIMCO Solo and C2 Strong-Fix, grip along their whole length and suit chipboard, MDF and fixing hardware such as hinges and brackets. Double countersunk heads sit flush with the surface, and most 3.5–5.0mm screws take a PZ2 pozi bit.

Indoors Or Outdoors?

Standard zinc and yellow screws such as the TIMCO Classic are made for dry, indoor use. Outside, choose a coated exterior screw such as TIMCO Decking Screws with their green exterior finish, or A2 stainless steel screws where corrosion resistance matters most, such as coastal areas, damp locations and oak, which can stain around plated screws.

Keep A Range In Stock

If you do a lot of different jobs, a mixed tray or an assorted box saves buying single sizes. Browse wood screws, coach screws and decking screws in our TIMCO and Screws & Fixings collections, with trade packs that bring down the price per box.

Frequently Asked Questions

What Size Screw Do I Need For 18mm Board?

A 4.0 x 40mm screw is a good starting point for fixing 18mm board, leaving about 22mm in the timber behind. Use 4.0 x 50mm if the base material is soft or you want extra holding power.

How Long Should A Wood Screw Be?

Aim for about two and a half times the thickness of the piece you are fixing, with at least half and ideally two thirds of the screw in the base timber.

What Is A No. 8 Screw In Metric?

A No. 8 gauge screw is roughly 4.0mm in diameter. A No. 6 is about 3.5mm and a No. 10 about 5.0mm.

Do I Need A Pilot Hole For Wood Screws?

In softwood a sharp modern screw often goes in without one, but always drill a pilot hole in hardwoods, near the ends and edges of boards and in brittle material to stop splitting.

Which Screws Should I Use Outside?

Use coated exterior screws, such as decking screws, or A2 stainless steel screws. Standard zinc and yellow screws are intended for dry, indoor use.