Visible screw heads and cam fittings are the quickest giveaway that furniture is flat-pack. Self-adhesive screw cover caps are thin printed discs that peel off a sheet and press over the hole, hiding the fixing in seconds. Pick the right size and colour and they almost disappear. This guide explains how to choose and fit them.
What Are Screw Cover Caps For?
Stick-on caps cover screw heads, nail holes, cam lock fittings and confirmat screws on kitchen carcasses, wardrobes, shelving, office furniture and flat-pack units. They are also handy for hiding old holes after you move a hinge or handle. Because they sit on the surface rather than in the hole, they work over almost any fixing that is flush with or just below the face of the board.
Which Size Do I Need?
Choose a cap a few millimetres wider than whatever you are covering, so the edge sits on clean board all the way round.
| Cap Size | Best For |
|---|---|
| 13mm / 14mm | Screw heads on carcasses and shelving, small holes, confirmat screws |
| 18mm | Standard cam lock fittings, larger screw heads and bigger holes |
| 20mm | Cam locks with a little margin to spare, damaged or slightly oversized holes |
Most standard cam lock fittings are around 15mm across, so an 18mm or 20mm cap covers them neatly. If you are not sure, measure the fitting and add 3–5mm.
How Many Caps Per Sheet?
Our own self-adhesive screw cover caps come in three sizes: 13mm with 20 caps per sheet, 14mm with 52 caps per sheet and 18mm with 36 caps per sheet, in packs from a single sheet up to trade quantities. They are made from PVC in popular finishes including white, black, light grey, dark grey, oak, light oak, walnut, pine and brushed aluminium effect.
For an exact match to a specific board decor, FOLDECOR screw cover caps come in 14mm (25 per sheet) and 20mm (28 per sheet) with around 70 colours and finishes in each size, grouped into families such as oak shades, white and cream, grey and black, walnut and dark wood, light woods, bright colours, and stone, concrete and metallic effects.
How To Match The Colour
- Compare colours in daylight against the actual board, not just on screen – monitors vary.
- For woodgrain boards, match the background tone rather than the darkest grain lines.
- If in doubt between two shades, the slightly darker one usually hides better than one that is too light.
- On a big job, buy a single sheet first to check the match before ordering more.
How To Fit Self-Adhesive Cover Caps
- Make the fixing flush. The screw head or cam should sit level with or just below the surface. A proud screw head will show through the cap.
- Clean the surface. Wipe away dust, sawdust and grease, then let it dry. Dirt and polish are the main reasons caps fall off.
- Peel and place. Lift a cap from the sheet by its edge, centre it over the fixing and press it down.
- Press firmly. Rub over the whole cap, especially the edge, with your thumb or a soft cloth so the adhesive beds in.
Fit caps at normal room temperature – adhesives grip poorly on cold surfaces. If you need to remove one later, lift the edge with a fingernail or thin blade and clean off any residue before fitting a new cap.
Hinged Fold-Over Caps: An Alternative
If you need to reach the screw again, a hinged cap may suit better. Häfele hinged fold-over cover caps have a washer that sits under the screw head and a hinged lid that snaps shut over it. They fit 6–8 gauge screws, are 14mm across and suit cabinets, panels, signs and number plates.
Finishing Touches
Exposed chipboard edges give furniture away just as quickly as screw heads. Pair your caps with matching melamine edging tape, and see our Home & Bedroom range for wardrobe fittings, door buffers and other small parts that finish a room.
Frequently Asked Questions
What Size Screw Cover Caps Do I Need For Cam Locks?
Most standard cam lock fittings are around 15mm across, so 18mm or 20mm caps cover them with a clean margin. Measure the fitting and add 3–5mm if you are unsure.
Why Do My Screw Cover Caps Keep Falling Off?
Usually because the surface was dusty, greasy or polished, or the screw head sits proud. Clean and dry the surface, make sure the fixing is flush and press the cap down firmly, especially around the edge.
Can I Paint Over Self-Adhesive Cover Caps?
It is better to choose a matching colour. Our caps come in common furniture finishes, and FOLDECOR caps offer around 70 colours per size for close matches to specific board decors.
How Many Caps Are On A Sheet?
Our 13mm sheets have 20 caps, 14mm sheets 52 caps and 18mm sheets 36 caps. FOLDECOR sheets have 25 caps at 14mm and 28 caps at 20mm.
Are Cover Caps Removable?
Yes. Lift the edge with a fingernail or thin blade, clean off any residue and fit a new cap. If you need regular access to the screw, hinged fold-over caps are a better choice.
